Velvacon Paints

Switching from 12V to 24V Trolling Motor Wiring. I’ve a boat not long ago i bought which had plant 12V 8 gauge wires and connect beforehand

Switching from 12V to 24V Trolling Motor Wiring. I’ve a boat not long ago i bought which had plant 12V 8 gauge wires and connect beforehand

  • Jul 8, 2015
  • # 1
  • chevync20

    Twelve Pointer

    I have a boat not long ago i bought that had plant 12V 8 measure wiring and connect at the start. My personal real question is, I would like to run a Minn Kota Powerdrive V2 70 LB 24V motor, but need certainly to update every thing to 24. I understand how-to wire batteries in parallel and collection, but have to know everything I should exchange. By wiring up in show to 24V, try two wire adequate on connect? Really does a 24V trolling motor have actually 4 cables? I’ve had 12V engines prior to now, but never any 24V setups. Anyone who can aim me personally within the proper path, i might greatly enjoy it.

    The 70 pound 24V brings a maximum of 42 amps, so I believed the 8 determine wiring would-be adequate. Any simple to follow hyperlinks is appreciated. I discover some in just two cable and a few with three and four. Simply want to verify I get every thing purchased and ready for if the motor comes. Thanks once again

    • Jul 8, 2015
  • number 2
  • Eric Revo

    Old Mossy Horns
    • Jul 8, 2015
  • no. 3
  • Dan in NC

    Six Tip
    • Jul 8, 2015
  • #4
  • catfishrus

    Twelve Pointer
    • Jul 8, 2015
  • no. 5
  • chevync20

    Twelve Pointer
    • Jul 8, 2015
  • no. 6
  • Eric Revo

    Past Mossy Horns
    • Jul 8, 2015
  • #7
  • sky hawk

    Past Mossy Horns

    As mentioned, 24v will pull considerably amps than 12v. Therefore if the wiring was actually enough for 12v, it should be sufficient when it comes down to 24v.

    Truly the only exception becoming any time you go the positioning with the electric batteries while increasing the distance. Point makes a difference. If not, and you’re simply swapping out, never make an effort modifying the wires.

    • Jul 8, 2015
  • #8
  • chevync20

    Twelve Tip
    • Jul 8, 2015
  • no. 9
  • Mr.Gadget

    Past Mossy Horns
    • Jul 8, 2015
  • #10
  • Mr.Gadget

    Old Mossy Horns

    As mentioned, 24v will pulling much less amps than 12v. So if the wires was adequate for 12v, it will likely be adequate the 24v.

    The actual only real exception to this rule getting any time you go the location of batteries while increasing the distance. Range is important. Or even, and you are just exchanging down, do not make the effort altering the wiring.

    • Jul 8, 2015
  • #11
  • chevync20

    Twelve Pointer
    • Jul 8, 2015
  • #12
  • Mr.Gadget

    Past Mossy Horns

    Yep think about it like h2o stream. if you want a 2″ water line but only have 1″ possible two contours to have the end require.

    Same way with energy. Possible operated 2 contours both operate 24v but going to the exact same plug you’ll be able to operate twice as much amps as merely working one line state line x operates 50 amps but 2 lines x/2 run 25 amps each providing the 50 amps.

    • Jul 8, 2015
  • #13
  • chevync20

    Twelve Tip
    • Jul 9, 2015
  • #14
  • heavens hawk

    Old Mossy Horns

    24V draws considerably recent than 12V. Therefore if it absolutely was adequate for 12, it’s more than enough for 24. You did get that parts right?

    There are numerous different gauges of line that will operate. The bigger the cable the significantly less current fall you should have. Presuming a 20′ wire (40′ circuit), 42 amp, 24V. 8 AWG must good. Personally, I will never operate heavier cable for a motor that’s going to draw much less current than what the manufacturing plant intended.

    Listed here is Minn Kota’s Conductor determine chart: (click the appropriate link)

    Realize that the 12V 55lb. thrust unit immediately above yours draws more amps and requires large measure line. In addition notice the advised circuit breaker is higher than the maximum amp draw of motor. That is because you don’t want they to visit any time you switch your motor chinalovecupid dating on large. Cannot place a 40 amp breaker on a 42 amp motor. Take into account that 95percent of times you’ll not suck anywhere close to 42 amps.

    Leave a Reply

    Your email address will not be published. Required fields are marked *